Interfacial Resistive Switching of Niobium-Titanium Anodic Memristors with Self-Rectifying Capabilities.

A broad compositional range of Nb-Ti anodic memristors with volatile and self-rectifying behaviour was studied using a combinatorial screening approach. A Nb-Ti thin-film combinatorial library was co-deposited by sputtering, serving as the bottom electrode for the memristive devices. The library, with a compositional spread ranging between 22 and 64 at.% Ti was anodically oxidised, the mixed oxide being the active layer in MIM-type structures completed by Pt discreet top electrode patterning. By studying I-U sweeps, memristors with self-rectifying and volatile behaviour were identified. Moreover, all the analysed memristors demonstrated multilevel properties. The best-performing memristors showed HRS/LRS (high resistive state/low resistive state) ratios between 4 and 6 × 105 and very good retention up to 106 successive readings. The anodic memristors grown along the compositional spread showed very good endurance up to 106 switching cycles, excluding those grown from alloys containing between 31 and 39 at.% Ti, which withstood only 10 switching cycles. Taking into consideration all the parameters studied, the Nb-46 at.% Ti composition was screened as the parent metal alloy composition, leading to the best-performing anodic memristor in this alloy system. The results obtained suggest that memristive behaviour is based on an interfacial non-filamentary type of resistive switching, which is consistent with the performed cross-sectional TEM structural and chemical characterisation.

Physical Trace Gas Identification with the Photo Electron Ionization Spectrometer (PEIS).

Chemosensor technology for trace gases in the air always aims to identify these compounds and then measure their concentrations. For identification, traceable methods are sparse and relate to large appliances such as mass spectrometers. We present a new method that uses the alternative traceable measurement of the ionization energies of trace gases in a way that can be miniaturized and energetically tuned. We investigate the achievable performance. Since tunable UV sources are not available for photoionization, we take a detour via impact ionization with electrons, which we generate using the photoelectric effect and bring to sharp, defined energies on a nanoscale in the air. Electron impact ionization is thus possible at air pressures of up to 900 hPa. The sensitivity of the process reaches 1 ppm and is equivalent to that of classic PID. With sharpened energy settings, substance identification is currently possible with an accuracy of 30 meV. We can largely explain the experimental observations with the known quantum mechanical models.

Evolution of Microstructure, Mechanical Properties, and Corrosion Resistance of Mg-2.2Gd-2.2Zn-0.2Ca (wt%) Alloy by Extrusion at Various Temperatures.

The current investigation involved casting the Mg-2.2Gd-2.2Zn-0.2Ca (wt%) alloy (GZX220) through permanent mold casting, followed by homogenization at 400 °C for 24 h and extrusion at 250 °C, 300 °C, 350 °C, and 400 °C. Microstructure investigations revealed that α-Mg, Mg-Gd, and Mg-Gd-Zn intermetallic phases were present in the as-cast alloy. Following the homogenization treatment, a majority of these intermetallic particles underwent partial dissolution into the matrix phase. α-Mg grains exhibited a considerable refinement by extrusion due to dynamic recrystallization (DRX). At low extrusion temperatures, higher basal texture intensities were observed. The mechanical properties were remarkably enhanced after the extrusion process. However, a consistent decline in strength was observed with the rise in extrusion temperature. The corrosion performance of the as-cast GZX220 alloy was reduced by homogenization because of the lack of corrosion barrier effect of secondary phases. A significant enhancement of corrosion resistance was achieved by the extrusion process.

Threshold Switching in Forming-Free Anodic Memristors Grown on Hf-Nb Combinatorial Thin-Film Alloys.

The development of novel materials with coexisting volatile threshold and non-volatile memristive switching is crucial for neuromorphic applications. Hence, the aim of this work was to investigate the memristive properties of oxides in a Hf-Nb thin-film combinatorial system deposited by sputtering on Si substrates. The active layer was grown anodically on each Hf-Nb alloy from the library, whereas Pt electrodes were deposited as the top electrodes. The devices grown on Hf-45 at.% Nb alloys showed improved memristive performances reaching resistive state ratios up to a few orders of magnitude and achieving multi-level switching behavior while consuming low power in comparison with memristors grown on pure metals. The coexistence of threshold and resistive switching is dependent upon the current compliance regime applied during memristive studies. Such behaviors were explained by the structure of the mixed oxides investigated by TEM and XPS. The mixed oxides, with HfO2 crystallites embedded in quasi amorphous and stoichiometrically non-uniform Nb oxide regions, were found to be favorable for the formation of conductive filaments as a necessary step toward memristive behavior. Finally, metal-insulator-metal structures grown on the respective alloys can be considered as relevant candidates for the future fabrication of anodic high-density in-memory computing systems for neuromorphic applications.

Impact of Electrolyte Incorporation in Anodized Niobium on Its Resistive Switching.

The aim of this study was to develop memristors based on Nb2O5 grown by a simple and inexpensive electrochemical anodization process. It was confirmed that the electrolyte selection plays a crucial role in resistive switching due to electrolyte species incorporation in oxide, thus influencing the formation of conductive filaments. Anodic memristors grown in phosphate buffer showed improved electrical characteristics, while those formed in citrated buffer exhibited excellent memory capabilities. The chemical composition of oxides was successfully determined using HAXPES, while their phase composition and crystal structure with conductive filaments was assessed by TEM at the nanoscale. Overall, understanding the switching mechanism leads towards a wide range of possible applications for Nb memristors either as selector devices or nonvolatile memories.

Comparative Behavior of Viscose-Based Supercapacitor Electrodes Activated by KOH, H2O, and CO2.

Activated carbons derived from viscose fibers were prepared using potassium hydroxide, carbon dioxide, or water vapor as activation agents. The produced activated carbon fibers were analyzed via scanning electron microscopy and energy dispersive X-ray spectroscopy, and their porosity (specific surface area, total pore volume, and pore size distribution) was calculated employing physisorption experiments. Activated carbon fibers with a specific surface area of more than 2500 m2 g-1 were obtained by each of the three methods. Afterwards, the suitability of these materials as electrodes for electrochemical double-layer capacitors (supercapacitors) was investigated using cyclic voltammetry, galvanostatic measurements, and electrochemical impedance spectroscopy. By combining CO2 and H2O activation, activated carbon fibers of high purity and excellent electrochemical performance could be obtained. A specific capacitance per electrode of up to 180 F g-1 was found. In addition, an energy density per double-layer capacitor of 42 W h kg-1 was achieved. These results demonstrate the outstanding electrochemical properties of viscose-based activated carbon fibers for use as electrode materials in energy storage devices such as supercapacitors.

Composite Memristors by Nanoscale Modification of Hf/Ta Anodic Oxides.

Composite memristors based on anodic oxidation of Hf superimposed on Ta thin films are studied. A layered structure is obtained by successive sputtering of Ta and Hf thin films. The deposition geometry ensured components' thickness gradient profiles (wedges) aligned in opposite directions. Anodization in citrate buffer electrolyte leads to a nanoscale columnar structuring of Ta2O5 in HfO2 due to the higher electrical resistance of the latter. Following the less resistive path, the ionic current forces Ta oxide to locally grow toward the electrolyte interface according to the Rayleigh-Taylor principle. The obtained composite oxide memristive properties are studied as a function of the Hf/Ta thickness ratio. One pronounced zone prominent for memristive applications is found for ratios between 4 and 5. Here, unipolar and bipolar memristors are found, with remarkable endurance and retention capabilities. This is discussed in the frame of conductive filament formation preferentially along the interfaces between oxides.

Femtosecond Laser-Processing of Pre-Anodized Ti-Based Bone Implants for Cell-Repellent Functionalization.

Microstructures and nanostructures can be used to reduce the adhesion of the cells on the auxiliary material. Therefore, the aim of our work was to fabricate laser-induced hierarchical microstructures and nanostructures by femtosecond laser-treatment (wavelength 1040 nm, pulse length 350 fs, repetition rates in the kHz range) to reduce the cell adhesion. Additionally, surface chemistry modification by optimized electrochemical anodization was used to further reduce the cell adhesion. For testing, flat plates and bone screws made of Ti-6Al-4V were used. Bone-forming cells (human osteoblasts from the cell line SAOS-2) were grown on the bone implants and additional test samples for two to three weeks. After the growth period, the cells were characterized by scanning electron microscopy (SEM). While earlier experiments with fibroblasts had shown that femtosecond laser-processing followed by electrochemical anodization had a significant impact on cell adhesion reduction, for osteoblasts the same conditions resulted in an activation of the cells with increased production of extracellular matrix material. Significant reduction of cell adhesion for osteoblasts was only obtained at pre-anodized surfaces. It could be demonstrated that this functionalization by means of femtosecond laser-processing can result in bone screws that hinder the adhesion of osteoblasts.

Electrolyte-Dependent Modification of Resistive Switching in Anodic Hafnia.

Anodic HfO2 memristors grown in phosphate, borate, or citrate electrolytes and formed on sputtered Hf with Pt top electrodes are characterized at fundamental and device levels. The incorporation of electrolyte species deep into anodic memristors concomitant with HfO2 crystalline structure conservation is demonstrated by elemental analysis and atomic scale imaging. Upon electroforming, retention and endurance tests are performed on memristors. The use of borate results in the weakest memristive performance while the citrate demonstrates clear superior memristive properties with multilevel switching capabilities and high read/write cycling in the range of 106. Low temperature heating applied to memristors shows a direct influence on their behavior mainly due to surface release of water. Citrate-based memristors show remarkable properties independent on device operation temperatures up to 100 °C. The switching dynamic of anodic HfO2 memristors is discussed by analyzing high resolution transmission electron microscope images. Full and partial conductive filaments are visualized, and apart from their modeling, a concurrency of filaments is additionally observed. This is responsible for the multilevel switching mechanism in HfO2 and is related to device failure mechanisms.

Gallium-Enhanced Aluminum and Copper Electromigration Performance for Flexible Electronics.

Wide range binary and ternary thin film combinatorial libraries mixing Al, Cu, and Ga were screened for identifying alloys with enhanced ability to withstand electromigration. Bidimensional test wires were obtained by lithographically patterning the substrates before simultaneous vacuum co-deposition from independent sources. Current-voltage measurement automation allowed for high throughput experimentation, revealing the maximum current density and voltage at the electrical failure threshold for each alloy. The grain boundary dynamic during electromigration is attributed to the resultant between the force corresponding to the electron flux density and the one corresponding to the atomic concentration gradient perpendicular to the current flow direction. The screening identifies Al-8 at. % Ga and Cu-5 at. % Ga for replacing pure Al or Cu connecting lines in high current/power electronics. Both alloys were deposited on polyethylene naphthalate (PEN) flexible substrates. The film adhesion to PEN is enhanced by alloying Al or Cu with Ga. Electrical testing demonstrated that Al-8 at. % Ga is more suitable for conducting lines in flexible electronics, showing an almost 50% increase in electromigration suppression when compared to pure Al. Moreover, Cu-5 at. % Ga showed superior properties as compared to pure Cu on both SiO2 and PEN substrates, where more than 100% increase in maximum current density was identified.

Overcoming intra-molecular repulsions in PEDTT by sulphate counter-ion.

We set out to demonstrate the development of a highly conductive polymer based on poly-(3,4-ethylenedithia thiophene) (PEDTT), PEDOTs structural analogue historically notorious for structural disorder and limited conductivities. The caveat therein was previously described to lie in intra-molecular repulsions. We demonstrate how a tremendous >2600-fold improvement in conductivity and metallic features, such as magnetoconductivity can be achieved. This is achieved through a careful choice of the counter-ion (sulphate) and the use of oxidative chemical vapour deposition (oCVD). It is shown that high structural order on the molecular level was established and the formation of crystallites tens of nanometres in size was achieved. We infer that the sulphate ions therein intercalate between the polymer chains, thus forming densely packed crystals of planar molecules with extended π-systems. Consequently, room-temperature conductivities of above 1000 S cm-1 are achieved, challenging those of conventional PEDOT:PSS. The material is in the critical regime of the metal-insulator transition.

Metal-Free Hydrogen-Bonded Polymers Mimic Noble Metal Electrocatalysts.

The most active and efficient catalysts for the electrochemical hydrogen evolution reaction (HER) rely on platinum, a fact that increases the cost of producing hydrogen and thereby limits the widespread adoption of this fuel. Here, a metal-free organic electrocatalyst that mimics the platinum surface by implementing a high work function and incorporating hydrogen-affine hydrogen bonds is introduced. These motifs, inspired from enzymology, are deployed here as selective reaction centres. It is shown that the keto-amine hydrogen-bond motif enhances the rate-determining step in proton reduction to molecular hydrogen. The keto-amine-functionalized polymers reported herein evolve hydrogen at an overpotential of 190 mV. They share certain key properties with platinum: a similar work function and excellent electrochemical stability and chemical robustness. These properties allow the demonstration of one week of continuous HER operation without notable degradation nor delamination from the carrier electrode. Scaled continuous-flow electrolysis is reported and 1 L net molecular hydrogen is produced within less than 9 h using 2.3 mg of polymer electrocatalyst.

Electrochemical Screening of Tungsten Trioxide-Nickel Oxide Thin Film Combinatorial Library at Low Nickel Concentrations.

The electrochemical behavior of a tungsten trioxide-nickel oxide (WO3-NiO) thin film library was investigated using scanning droplet cell microscopy (SDCM) in 0.1 mol dm-3 sodium perchlorate (NaClO4) solution. The WO3-Ni film library was deposited by thermal coevaporation on an indium tin oxide (ITO)-coated glass substrate in an atomic Ni concentration range from 2.8 to 15.6 at. %. After an oxidation/crystallization heat treatment, the Ni was oxidized and the crystal structure of WO3-NiO was transformed from monoclinic WO3 (3.5 at. % Ni) to cubic WO3 (up to 7.1 at. % Ni) and again to monoclinic WO3 when the Ni amount increased (>11.8 at. %). Proton (H+) intercalation (cathodic reaction) and deintercalation (anodic reaction) into the WO3-NiO mixed phases was induced. Electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) analysis revealed that the WO3-NiO film has n-type bilayer capacitive property, with the outer capacitive layer having a higher defect density than the inner capacitive layer. With a Ni concentration of 7.1 at. %, the WO3-NiO film was the most defective in the library. Introduction of the Ni cation into the WO3 network was associated with changes of the semiconducting properties of the film.

Enhanced Bio-Electrochemical Reduction of Carbon Dioxide by Using Neutral Red as a Redox Mediator.

Microbial electrosynthetic cells containing Methylobacterium extorquens were studied for the reduction of CO2 to formate by direct electron injection and redox mediator-assisted approaches, with CO2 as the sole carbon source. The formation of a biofilm on a carbon felt (CF) electrode was achieved while applying a constant potential of -0.75 V versus Ag/AgCl under CO2 -saturated conditions. During the biofilm growth period, continuous H2 evolution was observed. The long-term performance for CO2 reduction of the biofilm with and without neutral red as a redox mediator was studied by an applied potential of -0.75 V versus Ag/AgCl. The neutral red was introduced into the systems in two different ways: homogeneous (dissolved in solution) and heterogeneous (electropolymerized onto the working electrode). The heterogeneous approach was investigated in the microbial system, for the first time, where the CF working electrode was coated with poly(neutral red) by the oxidative electropolymerization thereof. The formation of poly(neutral red) was characterized by spectroscopic techniques. During long-term electrolysis up to 17 weeks, the formation of formate was observed continuously with an average Faradaic efficiency of 4 %. With the contribution of neutral red, higher formate accumulation was observed. Moreover, the microbial electrosynthetic cell was characterized by means of electrochemical impedance spectroscopy to obtain more information on the CO2 reduction mechanism.

Testosterone- and vitamin-grafted cellulose ethers for sustained release of camptothecin.

Camptothecin (CPT), a potent anticancer drug with known antiviral activity, is halted of clinical use. Few drug delivery systems of CPT are approved for therapy. Hereby, we propose the encapsulation of hydrophobic CPT in the inner core of cellulose nanoaggregates for sustained release with retaining of antiproliferative activity. Cellulose conjugates were synthesized by esterification of methyl cellulose, hydroxyethyl cellulose and (hydroxypropyl)methyl cellulose with testosterone, ergocalciferol and dl-α-tocopherol hemisuccinates. The degree of substitution attained ranged from 0.004 to 0.025 and no depolymerization was observed by size exclusion chromatography. ATR-FTIR and NMR spectroscopies confirmed grafting of testosterone and vitamins to celluloses. According to dynamic light scattering, it resulted in their self-assembly in aqueous medium as stable and slightly negatively charged nanoaggregates of 213 to 731 nm. Nanoaggregates formation was also assessed using transmission electron and atomic force microscopies. CPT was encapsulated in the cellulose nanoaggregates, achieving a content of 1.7-13.0 wt %. Sustained release of camptothecin over 150 h was observed in simulated physiological conditions. CPT-loaded cellulose nanoparticles appeared to be possible candidates for chemotherapy, according to observed cytotoxicity against MCF-7 cancer cells.

Insight into Antimicrobial Properties via Self-Acidification of Compounds from the Molybdenum-Tungsten-Oxygen System.

This communication is focused on the synthesis, characterization and experimental proof of the mechanism of antimicrobial activity of powders from the molybdenum-tungsten-oxygen (Mo-W-O) system. Materials with a discrete ratio of Mo/W ranging from 100% MoO3 to 100% WO3 with a stepwise increase of 5-10 wt % W were synthesized by the spray drying method following calcination. Spherical hollow particles with a broad size distribution were formed and the composition influenced the crystalline phases in such a way that either pure and/or mixed oxides (Mo0.6W0.4O3) were obtained. A good correlation between composition variation and phases present on the antimicrobial activity is obtained and provides a detailed screening of the activity efficiency versus compositional transition. Antimicrobial tests were performed against a model Gram-negative bacterium (Escherichia coli). Furthermore, the mechanism of antimicrobial activity is proven by correlating the medium acidification via pH measurements to the bacteria lifespan at low pH values. The mechanism is additionally supported by the bacterial growth when a buffered nutrient medium was used, together with the evidence that the powder particles have no disruptive effect on the cell wall. Consequently, an extended mechanism is proposed for the mixed oxide, relating both the structure and solubility results. Solubility measurements displayed a steep decrease in metal ions concentration with the addition of W. A narrow compositional range was identified (80 to 60 wt % Mo) where the antimicrobial activity was present, which is concurrent with a very strong decrease in solubility. Materials within this range show adequate features for being implemented into hybrid systems consisting of inorganic materials-polymers/varnishes that can be used for touch surfaces in healthcare settings.

Strong Volta potential change in doped zinc oxide as a photoresponse to UV irradiation.

Doped ZnO thin films on ITO substrates were prepared by reactive co-sputtering of ZnO and several dopant metals, namely Al, Mn, Ti, W or Zr. To elucidate the influence of the dopant, morphological and compositional investigations were performed applying SEM/EDX, XRD and AFM. The optical band gaps of the materials were determined by UV-VIS measurements and the subsequent analysis of the derived Tauc plots. SKP (Scanning Kelvin Probe) measurements were performed under alternating illumination periods in order to measure the CPD (contact potential difference) response on UV irradiation; effective donor concentrations were calculated from the SKP results. The obtained X-ray diffractograms revealed that W : ZnO is amorphous, whereas all other dopants form crystalline structures with diffraction angles shifted towards lower values. SEM and AFM imaging revealed a significant influence of the dopant on the film morphology. The optical band gap values are in the range of the ZnO value (∼3.30 eV), with the lowest value of 3.29 eV being measured for Mn : ZnO. An exception was found for W : ZnO, which exhibits significant band gap widening reaching 4.35 eV. The effective donor concentrations are low for all samples under dark conditions, whereas they showed enhanced values under illumination. The sensitivity of all materials towards illumination makes them promising candidates for future research activities in the field of photovoltaics.

Basic properties mapping of anodic oxides in the hafnium-niobium-tantalum ternary system.

A thin film combinatorial library deposited by co-sputtering of Hf, Nb and Ta was employed to characterise fundamental properties of the Hf-Nb-Ta system. Compositional mappings of microstructure and crystallography revealed similarities in alloy evolution. Distinct lattice distortion was observed upon addition of hexagonal Hf, leading to amorphisation of alloys containing more than 32 at.% Hf and less than 27 and 41 at.% Nb and Ta, respectively. Volta potential and open circuit potential mappings indicated minimal values for the highest Hf concentration. Localised anodisation of the library by scanning droplet cell microscopy revealed valve metal behaviour. Oxide formation factors above 2 nm V-1 were identified in compositional zones with high amounts of Nb and Ta. Fitting of electrochemical impedance spectroscopy data allowed electrical permittivity and resistivity of mixed oxides to be mapped. Their compositional behaviours were attributed to characteristics of the parent metal alloys and particularities of the pure oxides. Mott-Schottky analysis suggested n-type semiconductor properties for all Hf-Nb-Ta oxides studied. Donor density and flat-band potential were mapped compositionally, and their variations were found to be related mainly to the Nb amount. Synergetic effects were identified in mappings of Hf-Nb-Ta parent metals and their anodic oxides.

Silver-, calcium-, and copper molybdate compounds: Preparation, antibacterial activity, and mechanisms.

Developing novel compounds with antimicrobial properties can be an effective approach to decreasing the number of healthcare-associated infections, particularly in the context of medical devices and touch surfaces. A variety of molybdate powders (Ag2MoO4, CaMoO4, CuMoO4 and Cu3Mo2O9) were synthesized and characterized, and Escherichia coli was used as a model gram-negative bacterium to demonstrate their antimicrobial properties. Optical density measurements, bacterial colony growth, and stained gel images for protein expression clearly showed that silver- and copper molybdates inhibit bacterial growth, whereas CaMoO4 exhibited no bactericidal effect. All tests were performed in both daylight and darkness to assess the possible contribution of a photocatalytic effect on the activity observed. The main mechanism responsible for the antibacterial effect observed for Ag2MoO4 is related to Ag+ release in combination with medium acidification, whereas for compounds containing copper, leaching of Cu2+ ions is proposed. All these effects are known to cause damage at the cellular level. A photocatalytic contribution to the antibacterial activity was not clearly observable. Based on the pH and solubility measurements performed for powders in contact with various media (ultrapure water and bacterial growth medium), silver molybdate (Ag2MoO4) was identified as the best antibacterial candidate. This compound has great potential for further use in hybrid powder-polymer/varnish systems for touch surfaces in healthcare settings.